Wattle and Daub Hollyhock Cottage
from £8.99
This is a selection of detailed 3D Prints designed by the amazing Printable Scenery
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
Scale:
Quantity:
This is a selection of detailed 3D Prints designed by the amazing Printable Scenery
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
This is a selection of detailed 3D Prints designed by the amazing Printable Scenery
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces). Some photos showing may just be 3D renders. If in doubt, contact us first.
Most of our models come in parts and need assembly. I have attempted to add an image of the parts but may have forgotten in some listings. 32mm scaled models may come in more parts as well due to not fitting on my print beds. Please contact me if you are in any doubts before purchasing.
For dimensions, please see the provided image. They are in millimetres and are an approximation only.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright PrintableScenery, provided as an officially licensed seller
